Prepare Overclocking Software
To overclock your graphics card, you’ll need two pieces of software. Firstly, you’ll need the software that can be used to set new speeds for your GPU. Secondly, you’ll need a program that can stress test your system to make sure the settings you’ve used are stable.
You may also want to download an optional third program that can monitor your GPU temperature. The overclocking software suggested below already does this, but it’s nice to have an external program that can be minimized to the system tray.
- For overclocking software, you should download MSI Afterburner from MSI.com.
- For stress testing software, you should download Heaven Benchmark.
- Finally, if you’d like an extra temperature and voltage monitor, you can download GPU temp.
Building You Mining Rig
Build your mining rig just like any other machine. Install the CPU, processor, etc. just as you would normally. If you’re going to go about building a mining rig with four or more GPUs then it is likely that risers will be involved. There are several reasons for risers:
- Most GPUs used for cryptocurrency mining take up at least two slots on the motherboard, while on plugging in physically to a single slot.
- GPUs require an X16 slot. Most motherboards only have one or two X16 slots. X16 slots have 16 bus lanes, allowing for much faster communication between the video card and the motherboard. However, this is completely unnecessary for mining purposes. Mining sends a small math problem to the card and awaits an answer. This is a very different use-case than a video game would have.
- Assuming your board did have enough X16 slots, the close proximity of the cards would make for a difficult time in cooling.
- Risers convert X1 slots to X16 slots over a USB 3.0 cable allowing your to plug X16 GPUs into X1 slots (again, bandwidth is not an issue here).
You can get risers for cheap from Amazon. After you’ve built your mining rig, installed all of the operating system and drivers, its a good idea to test everything and make sure it works reliably. I would recommend mining for it with at least a few hours before you being the overclocking process.
Get a GPU Overclocking Software Suite
Bar none the easiest way to go about overclocking a mining GPU (or multiple GPUs) is to use a free product from MSI called Afterburner. Afterburner works on any GPU regardless of brand (no need to buy an MSI version of the GPU). Using Afterburner you’ll be able to modify all sorts of settings on your GPU from a single pane of glass. However, the items of most importance are front and center:
- Core Voltage – This controls the voltage input of the core GPU. Lower voltages may use less power. Generally leave this alone.
- Power Limit – Controls the Max power the GPU is allowed to consume. You can usually get away with setting this between 65% to 85% without reducing performance.
- Temp Limit – Sets the maximum temperature of the GPU before throttling or shutdown occurs.
- Core Clock (Mhz) – The core GPU speed, can usually be set to -75 or -100 without affecting performance.
- Memory Clock (Mhz) – This is the most important setting for mining. Some cards can go as much as +800 Mhz!
- Fan Speed – Generally leave this on auto and let the GPU decide. Higher settings may reduce fan life.
There are many other settings, but I recommend you ignore them unless you’re an expert tuner. You might be able to get another 1% to 2% performance from your card, but you might also significantly reduce its lifespan if you’re not sure what the setting actually does. You’ve been warned.
After your mining rig has been mining for a few hours and has proven itself to be stable, it is time to overclocking it. Overclocking a mining GPU can be fun, but it doesn’t have to also be frustrating! If you follow these steps, I promise it will be fun!
Bring up MSI Afterburner and your mining software’s output screen (such as Claymore’s command window). (Hint: If you need more help with selecting mining software, check out our article on Mining Software and Wallets.) You’ll want to make all of these changes while your machine is mining and watch the output screens to see if they are having the desire effect.
Begin the Overclocking Process
We’re now ready to being the process of overclocking a mining GPU! Start by setting the sliders to these numbers and then hitting apply. These settings will be applied to all cards on the system that are the same model. If you have numerous different cards you will need to make this change on each card manually.
- Core Voltage – No change
- Power Limit – 85%
- Temp Limit – 70c
- Core Clock (Mhz) – -50Mhz
- Memory Clock (Mhz) – No change
- Fan Speed – Auto
Let the miner continue to mine for about 10 minutes and make sure the hashrate is unaffected. If shouldn’t change. If you have errors in Claymore, then set them slowly raise them back until the errors go away. Then make the following change:
- Memory Clock (Mhz) – +400Mhz
Let the miner continue to mine for about 10 minutes. You should see a decent increase in your hashrate. If you start seeing errors slowly remove 50Mhz at a time until the errors go away. Be sure to hit the Apply button and wait a few minutes between. If the card performs well at +400Mhz (it most definitely should) then proceed to add +50Mhz every 5 or so minutes until you start seeing errors. Most cards can easily handle +500Mhz. Some of the better cards can handle all of the way up to +800Mhz! If you used the GTX 1060 from my GPU mining rig, you should be able to get the max performance settings to work.
After you find the memory clock that is stable, start lowering the core clock and power limit -5 at a time until errors occur, and then raise it back up to the last increment it was stable. You should be at the most optimal mining settings at that point.
That’s it! You’ve successfully overclocked your mining GPU!